Smart-UPS 750/1000/1500/2200/3000 VA 120/230 Vac Tower 1 Overview Product Description The APC® by Schneider Electric Smart-UPS® 750-3000 VA 120/230 Vac Tower is a high performance Uninterruptible Power Supply (UPS). It provides protection for electronic equipment from utility power. Troubleshooting Use the table below to solve minor Back-UPS ES installation or operation problems. Consult APC Online Technical Support or call APC Technical Support for assistance with problems that cannot be resolved using the table below.
Size:Download
4:STORAGE, MAINTENANCE, ANDTRANSPORTING
Storage
Store the UPS covered and positioned as for proper functioning, in a cool, dry location, with the batteries fully charged.
At
At +30 to +45 °C (+86 to +113 °F), charge the UPS battery every three months.
Replacing the Battery Module
This UPS has an easy to replace,
Once the battery is disconnected, the connected equipment is not protected from power outages.
Be careful during the following
Refer to Installing and Connecting the Battery and Attaching the Front Bezel, in this manual. Refer to Mounting the UPS in a Rack(Steps 1 and 2) for instructions on battery removal.
Be sure to deliver the spent battery to a recycling facility or ship it to APC in the replacement battery packing material.
Disconnecting the Battery for Transport
Always DISCONNECT THE BATTERY before shipping in compliance with U.S. Department of Transportation (DOT) regulations.
The battery may remain in the UPS; it does not have to be removed.
1.Shut down and disconnect any equipment attached to the UPS.
2.Shut down and disconnect the UPS from the power supply.
3.Remove the front bezel, and unplug the battery connector, by pulling firmly on white battery cord.
For shipping instructions and to obtain appropriate packing materials contact APC at the web site, www.apc.com/support/contact.
9
5:TROUBLESHOOTING
Use the chart below to solve minor
10
11
120V/230V Models: When the UPS is off and there is no utility power, use the cold start feature to apply power to the connected equipment from the UPS battery.
Cold start is not a normal condition.
Press and hold the button, (for about 3 seconds). The unit will beep, the LED lights will flash, and the unit will beep a second time. Release the ON button during the second beep. This will supply immediate power to the UPS and the connected equipment. Make sure connected equipment is switched to ON.
UPS OPERATES ON BATTERY ALTHOUGH NORMAL LINE VOLTAGE EXISTS
UPS input circuit breaker tripped.
Very high, low, or distorted line voltage. Inexpensive fuel powered generators can distort the voltage.
Reduce the load on the UPS by unplugging equipment and resetting the circuit breaker (on the back of UPS) by pressing the plunger in.
Move the UPS to a different outlet on a different circuit. Test the input voltage with the utility voltage display (see below). If acceptable to the connected equipment, reduce the UPS sensitivity.
BATTERYCHARGE ANDBATTERYLOADLEDS FLASH SIMULTANEOUSLY
The internal temperature of the UPS has exceeded the allowable threshold for safe operation.
Check that the room temperature is within the specified limits for operation.
Check that the UPS is properly installed allowing for adequate ventilation.
Allow the UPS to cool down. Restart the UPS. If the problem continues contact APC at, www.apc.com/supoport.
DIAGNOSTICUTILITYVOLTAGEFEATURE
The UPS starts a
12
Service
If the UPS requires service do not return it to the dealer. Instead, follow these steps:
1.Review the problems discussed in the Troubleshooting section of this manual to eliminate common problems.
2.If the problem persists, contact APC Customer Service through the APC web site, www.apc.com/support.
!Note the model number of the UPS, the serial number, and the date purchased. If you call APC Customer Service, a technician will ask you to describe the problem and try to solve it over the phone, if possible. If this is not possible, the technician will issue a Returned Material Authorization Number (RMA#).
!If the UPS is under warranty, repairs are free. If not, there is a repair charge.
3.Pack the UPS in its original packaging. If the original packing is not available, refer to the APC web site, www.apc.com/support, for information about obtaining a new set.
!Pack the UPS properly to avoid damage in transit. Never use Styrofoam beads for packaging. Damage sustained in transit is not covered under warranty.
Always DISCONNECT THE BATTERY before shipping in compliance with U.S. Department of Transportation (DOT) regulations.
The battery may remain in the UPS; it does not have to be removed.
4.Mark the RMA# on the outside of the package.
5.Return the UPS by insured, prepaid carrier to the address given to you by Customer Service.
Contacting APC
13
Regulatory Agency Approvals and Radio Frequency Warnings
230V MODELS
This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take corrective actions.
120V MODELS
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Shielded signal cables must be used with this product to ensure compliance with the Class A FCC limits.
BSMI
100V MODELS
14
Declaration of Conformity
Limited Warranty
American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. To obtain service under warranty you must obtain a Returned Material Authorization (RMA) number from customer support. Products must be returned with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment that has been damaged by accident, negligence, or misapplication or has been altered or modified in any way. This warranty applies only to the original purchaser who must have properly registered the product within 10 days of purchase.
EXCEPT AS PROVIDED HEREIN, AMERICAN POWER CONVERSION MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL APC BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, APC is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.
Entire contents copyright 2006 by American Power Conversion Corporation. All rights reserved. Reproduction in whole or in part without permission is prohibited.
APC, the APC logo,
15
1< Back= Page 2 =2
Size:Download
English
APC
750/1000/1500 VA
100/120/230 Vac
2U
Uninterruptible Power Supply
Introduction
The APC Uninterruptible Power Supply (UPS) is designed to prevent blackouts, brownouts, sags, and surges from reaching your computer and other valuable electronic equipment. The UPS filters small utility line fluctuations and isolates your equipment from large disturbances by internally disconnecting from the utility line. The UPS provides continuous power from its internal battery until the utility line returns to safe levels or the battery is discharged.
1:INSTALLATION
Read the Safety Instruction sheet before installing the UPS.
Unpacking
Inspect the UPS upon receipt. APC designed robust packaging for your product. However, accidents and damage may occur during shipment. Notify the carrier and dealer if there is damage.
The packaging is recyclable; save it for reuse or dispose of it properly.
Check the package contents. The package contains the UPS, the front bezel, the rail kit, and a literature kit containing:
•Product documentation and safety information
•
•PowerChute®
•Serial and USB communication cables
•Two IEC jumper cables and one plug adaptor (230V models only)
The UPS is shipped with the battery disconnected.
Rail Installation
Install the rails following instructions in the rail kit.
Mounting rails are supplied for the standard
13
1
Positioning the UPS
Place the UPS where it will be used. The UPS is heavy. Select a location sturdy enough to handle the weight.
Do not operate the UPS where there is excessive dust or the temperature and humidity are outside the specified limits.
0º40ºC
PLACEMENT
Mounting the UPS in a Rack
The UPS is heavy. To lighten it, you may remove the battery before mounting the unit in the rack (Steps 1 and 2).
Step 3
Install the UPS at or near the bottom of the rack (Step 3).
Check to ensure the rack will not tip after installing the UPS into the rack.
Be750g Manual
2
Installing and Connecting the Battery and Attaching the Front Bezel
Connect battery plug to UPS. Tuck white battery cord into space above connector.
Connecting Equipment and Power to the UPS
100/120V Models
![]()
120V Model Only: Site wiring fault indicator
230V Models
3
1.Connect equipment to the UPS. Note: Do not connect a laser printer to the UPS. A laser printer draws significantly more power than other types of equipment and may overload the UPS.
2.Add any optional accessories to the
3.Using a power cord, plug the UPS into a
100V/120V models: The power cord is permanently attached to the rear panel of the UPS. The INPUT plug is a NEMA
230V models: The power cord is supplied by the customer. Connect ground leads to the TVSS screw (optional). To make the connection, loosen the screw and connect the surge suppression device’s ground lead. Tighten the screw to secure the lead.
4.Turn on all connected equipment. To use the UPS as a master ON/OFF switch, be sure all connected equipment is switched ON. The equipment will not be powered until the UPS is turned on.
5.To power up the UPS press the button on the front panel.
•The UPS charges its battery when it is connected to utility power. The battery charges to 90% capacity during the first four hours of normal operation. Do not expect full battery run capability during this initial charge period.
•120V Models: Check the site wiring fault LED located on the rear panel. It lights up if the UPS is plugged into an improperly wired utility power outlet. Refer toTroubleshooting in this manual.
6.For additional computer system security, install PowerChute®
BASICCONNECTORS
Use an APC supplied cable to connect to the Serial Port. DO NOT use a standard serial interface cable since it is incompatible with the UPS connector.
Both Serial and USB Ports are provided. They cannot be used simultaneously.
Apc Es 750 Replacement Battery
TVSS Screw The UPS features a transient voltage
When connecting grounding cable, disconnect the UPS from utility power.
4
Power On
Power Off
This LED illuminates to indicate the UPS is compensating for a high utility voltage.
This LED illuminates to indicate the UPS is compensating for a low utility voltage.
When the on battery power LED is lit the UPS is supplying battery power to the connected equipment. When on battery, the UPS sounds an
The LED illuminates and the UPS emits a sustained alarm tone when an overload condition occurs.
5
Replace Battery
Battery
Disconnected
Automatic
Manual
Failure of a battery
The replace battery LED flashes and short beep is emitted every two seconds to indicate the battery is disconnected.
The UPS performs a
During the
If the UPS fails the
Press and hold the button for a few seconds to initiate the
On Battery Operation
The
Apc Back-ups Es 750 Manual
Press the button (front panel) to silence the UPS alarm (for the current alarm only). If the utility power does not return, the UPS continues to supply power to the connected equipment until the battery is exhausted.
If PowerChute® is not being used you must manually save your files and turn off the computer before the UPS fully discharges the battery.
DETERMININGONBATTERYRUNTIME
UPS battery life differs based on usage and environment. It is recommended that the battery/batteries be changed once every three years. See the APC web site, www.apc.com, for on battery run times.
6
Apc Battery Backup Manual
3:USERCONFIGURABLEITEMS
NOTE: SETTINGS ARE MADE THROUGH SUPPLIEDPOWERCHUTE SOFTWARE OR OPTIONALSMARTSLOT
ACCESSORY CARDS.
7
NOTE: SETTINGS ARE MADE THROUGH SUPPLIEDPOWERCHUTE SOFTWARE OR OPTIONALSMARTSLOT
Apc Be750g Manual
ACCESSORY CARDS.
Apc Back-ups Es 750 Manual
Apc Back Ups Es 750 User Manual
8
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |